We are a reputed organization that is engaged in manufacturing, supplying and exporting a wide variety of PTFE Rods. Our range has a working temperature range of minus 400°F to 500°F, excellent thermal & electrical insulation properties and a low coefficient of friction. With a non-stick surface, very few material will adhere to it and those that stick can easily be peeled or rubbed off. PTFE’s mechanical properties are lower than other engineering plastics, but that can be improved by adding fillers such as glass fiber, carbon, graphite, molybdenum disulfide and bronze. PTFE extruded rods diameter range from 8mm up to 150mm. PTFE is the most chemical resistant and the best dielectric of all known plastics. It is not aging and binding. These can be used from -180oC to +260oC under no burden circumstances. PTFE has the lowest coefficient of friction of all known solid material PTFE rod divide into mold rod and extruded rod.


  • High chemical resistance
  • High temperature resistance
  • Non-contaminating
  • Maintenance free
  • Long durability
  • Self lubricating

Data Sheet:

Properties Unit Result
Apparent Density g/cm3 2.10 ~ 2.25
Tensile Strength (min) Mpa 15
Crack Elongation (min) % 150

Our organization is engaged in manufacturing, supplying and exporting a vast array of PTFE Skived Sheets. PTFE resin is first mounded into round blank and then skived. The PTFE resin skived sheet and plates are highly dielectric, chemical resistant and not aging .They have a wide range of operation temperature. Our PTFE skived sheets exhibit very even and shining surface suitable for making pre-cut gasket, die cut gaskets, insulation barrier and non stick applications.


  • Electric insulation
  • Anti-caustic parts
  • Mechanical sealing and lubrication material
  • PTFE sheets
  • PTFE skived sheets
  • PTFE plates
  • Teflon sheets
  • Teflon plates
  • PTFE board
  • PTFE film

Data Sheet:

Properties Unit Result

Grade B Grade A
2.10-2.30 2.10-2.30
20 28
250 300
10 12
Apparent density g/cm3
Tensile strength≥ MPa
Crack elongation≥ %
Dielectric strength≥ Kv/mm

Size Available

Unit Options Available
Width Length
300 mm 300 mm
600 mm 600 mm
1 mtr 1 mtr
2 mtr 2 mtr
0.1, 0.2, 0.5, 0.7, 0.9, 1
1,2, 2.5, 3, 3.5, 4, 5,6

We have gained expertise in manufacturing, supplying and exporting a quality range of PTFE Molded Tubes. These products are molded in all the standard sizes. Minimum length available is 100 mm long to 150 mm long. Our range can be molded with special fillers like glass filled PTFE, carbon filled PTFE and bronze filled PTFE. Clients can avail these products in various colors.


To make machined components from this bush used for insulation application.

Size Available: 

  • Virtually any size with outer dia max: 300 mm and inner dia max 280 mm
  • Wall thickness of the bush should be minimum 5 mm
  • Length should be: 100 mm to max 150 mm

Data Sheet:

Properties Unit Result
Apparent Density g/cm3 2.1 ~ 2.3
Tensile Strength (min) Mpa 18
Crack Elongation (min) % 230

Made available by us is an extensive array of PTFE O Rings. These rings are made for some of the critical applications where rubber/elastomer fail to give chemical resistance. We offer FEP encapsulated silicon and viton core o-ring for pumps and mechanical seal applications. These o-rings are made by matching PTFE bush to require cross section size. The offered rings are machined to close tolerance and surface is free from kick marks and burr.

Sizes Available: Any size as per standard American dash size, JIS, BS


  • Pumps
  • Valves
  • Mechanical seals
  • Medical instruments
  • Ultra pure liquid handling systems

Data Sheet:

Compressibility 350 bar 7% ~ 9%
Recovery in 350 bar 7%
Tensile Strength 15Mpa
Density 2.2 ~ 2.4g/cm3
Pressure 20Bar
Temperature -180°C ~ 260°C